輸送燃油泵 200cyz-63柴油自吸泵 泵配90kw-4電機銅葉輪口徑200流量280立方

   我公司是一個生産齒輪油泵和螺杆泵的專業公司。公司擁有各種設備80台,主要設備有：c6140 cw6163c車床24台，tx611c/4镗床2台，m131m7130磨床8台，c125a立車2台，y318k y3150e滾齒機6台，e3050x16/1搖臂鑽床2台，e5163立式鑽床2台，b1-400萬能銑床3台，螺杆泵轉子專用qh2-007銑床1台，半自動螺旋轉子qh2-029b銑床2台，x53k立銑3台，半自動螺旋轉子qh2-031 qh2-032磨刃機台。my company is a company specialized in the production of gear oil pump and screw pump.company has 80 sets of various devices, the main equipment are: c6140 cw6163c 24 sets of lathe, tx611c/boring machine 2 units, 4 m131m7130 grinding machine 8 units, c125a set, 2 sets, y318k y3150e hobbing machine 6 units, e3050x16/1 radial drilling machine 2 sets, e5163 vertical drilling machine 2 sets, b1-400 universal milling machine 3 units, screw pump rotor 1 qh2-007 milling machine, semi-automatic screw rotor qh2-029 - b milling machine 2 sets, x53k three vertical milling, semi-automatic screw rotor qh2 qh2-031-031 edge grinding machine is used.

   我公司擁有省計量局制試驗台1台，自制試驗台3台，使生産産品從原材料投入到産成品出廠實現了全過程檢測。産品出廠合格率100%，具備較強的(de)綜合配套制造能力。理化試驗室、長度計量室是國家計量确認合格單位，使産品從原材料投入到産成品出廠實現了全過程檢測。産品出廠合格率100%，具備較強的綜合配套制造能力，公司年可生産各種泵6000多台。my company has the province system test bench 1 bureau of standard measurement, homemade test-bed 3 units, production of products from raw materials into finished goods factory implements the whole process of detection.product factory qualified rate 100%, have strong ability of comprehensive manufacturing.physical and chemical laboratory, length measuring room is the national metrological confirmation unit, make our products from raw materials into finished goods factory implements the whole process of detection.product factory qualified rate 100%, have strong comprehensive manufacturing capacity, company can produce all kinds of pump in more than 6000 units.

運費說明:

   1.本公司常規産品1-3天發貨,特殊要求或者需定做的産品發貨時間已與客戶協商為準, 2.泵運費方式有兩種:快遞和物流.小泵和小型配件發快遞,其餘體積較大,數量較多,推薦走專線物流貨運,一般南方,中部地區及沿海地區3-5天左右到達.西部,北部較遠的地區以及少數二次中轉地區5-8天左右可到,具體覆蓋範圍請咨詢公司客服人員.安裝使用:請您根據産品說明書的(de)步驟進行操作,如有問題,請聯系我公司.為了(le)保護您的(de)利益,我們已經提醒客戶在收到貨物時,要開箱驗貨,如在打開驗貨時發現貨物丢失,損害或者不符,請拒絕簽收,您簽收就代表已準确無誤的收到後屋,若在簽收貨物之後才發現貨物丢失或者不符,如不負責.客戶收到貨後,産品無法安裝或者規格有誤,本公司提供退貨或者換貨服務,退貨或者換貨的(de)客戶請保證貨物的完好無損,并承擔往返運費.客戶收到後,如果産品存在質量問題,請在收貨後7天内聯系我公司,提供相關質量問題圖片,我公司将在第一時間給您退貨或者換貨,因為我公司已經在發貨前已經仔細檢查過,所以過期将不提供此項服務,還請諒解.shipping details:1. our regular products 1-3 days of delivery, special requests or need to custom-made product delivery time is already negotiate with customer, 2. the pump freight way has two kinds: express and logistics. small pump and small accessories send express, the rest of the volume is larger, the number is more, recommend special line logistics, freight, generally south, central and coastal area about 3 to 5 days to arrive. in the west, north of remote areas and areas inhabited by minority secondary transit, about five to eight days to specific coverage please consulting company customer service staff. install and use, please according to the product manual steps, if any problem, please contact our company, we advise you that we will be the most professional and technical personnel to provide service for you. in order to protect your interests, when we have to remind the customer receive the goods, unpacking inspection, such as when open the inspection found that the goods lost, damage or discrepancy, please refuse to sign after receiving sth, you sign after receiving sth means have accurate received after the house, if after receipt of goods found the goods didn\'t agree lost or, if not responsible. customers after receiving the goods, the product can\'t install or specification is wrong, the company provides the return or exchange service, return or exchange the customers please make sure that the goods are intact, and bear the freight back and forth. the receipt of the customer, if the product quality problems, please contact me within 7 days after receiving the company, provide relevant quality problem photos, our company will give you a refund or a replacement in the first time, because i already have carefully checked before shipment, so late will not provide this service, also please understand.

    自吸泵的自吸高度，與葉輪前密封間隙、泵的(de)轉數、分離室液面高度等因素有關。葉輪前密封間隙越小，自吸高度越大，一般取為0.3~0.5毫米；在間隙增大時，除自吸高度下降外，泵的(de)揚程、效率均降低。泵的(de)自吸高度随葉輪的圓周速度u2的增大而增大，但到最大自吸高度時，轉數增加而自吸高度就不再增加了，此時隻是縮短自吸時間；當轉數下降時，自吸高度則随着下降。在其它條件不變的(de)情況下，自吸高度還随着儲水高度的(de)增加而增加（但也不能超過分離室的(de)儲水高度）。為了(le)在自吸泵中更好地使氣水混合，葉輪的(de)葉片須少些，使葉栅的節距增大；并宜采用半開式葉輪（或葉輪槽道較寬的(de)葉輪），這樣更方便于回水深入地射進葉輪葉栅中。
自吸泵大部分與内燃機配套，裝在可移動的(de)小車上，宜于野外作業。self-g pump self-g height, and before the impeller seal clearance, the revolutions of the pump, separation chamber level and other factors.before the impeller seal gap is smaller, the greater the self-g height, general take 0.3 ~ 0.5 mm;increase in clearance, in addition to the self-g height decreased, pump lift and efficiency are reduced.the self-g pump
    自吸油泵的(de)使用及維護
    1 啟動前的準備及檢查事項1 to start preparing and check the item before
    1.1 檢查軸承體油腔中潤滑油是否已達到規定要求，潤滑油的(de)油位應保持在機油尺的兩刻線之間或油标中線位置,不得過多或不足.1.1 check whether oil bearing body cavity, the lubricating oil has reached the specified requirements, the lubricating oil in the oil level should be kept in the oil foot or oil standard midline position between two scribed line, not too much or not.
    1.2 檢查泵體内的儲液是否高于葉輪邊緣.如若不足,可以從泵體上的加液口直接向泵體内注入儲液,不應在儲液不足的情況下啟動運轉,否則泵體不能正常工作,且易損壞機械密封.1.2 check reservoir is higher than that of the impeller in the pump body. if not, can add liquid mouth from the pump body directly to the pump body into the reservoir, the defects in the reservoir should not start operation, under the condition of pump body can not work normally, and easy to damage the mechanical seal.
    1.3 檢查泵轉動部件是否有卡住磕碰現象.1.3 check the pump rotating components for stuck knock against.
    1.4 檢查泵體底腳及各連接處有無松動現象.1.4 check the pump body foot and joint have loose phenomenon.
    1.5 檢查泵軸與原動機主軸的同軸度與平衡度.1.5 check the pump shaft and prime mover of main shaft alignment and balance.
    1.6 檢查進口管路是否漏氣1.6 check whether import pipeline leak
    1.7 打開吸入管道的(de)閥門(注意不要全開)1.7 open the suction piping valves (be careful not to open)

    2 啟動及操作2 start-up and operation
    2.1 啟動油泵,注意泵軸的轉向是否正确2.1 start the oil pump, pay attention to the steering pump shaft is correct
    2.2 注意轉動時有無異常噪音和振動2.2 notice there is no abnormal noise and vibration
    2.3 注意真空表讀數,啟動後當壓力表及真空表的(de)讀數經過一段時間的波動而時針穩定後,說明泵内已經上液,油泵竟如正常工作狀體.2.3 pay attention to the vacuum meter reading, starts when the pressure gauge and vacuum gauge readings over a period of time after hour due to the variation of stable, explain within the pump has been on fluid, oil pump body become like a normal job.
    2.4 在泵進入正常輸油作業前,應特别注意泵内油溫升高情況,如果這個過程長,泵内油溫過高,則應停泵檢查原因.2.4 before the pump into the normal oil operation, should pay special attention to pump the high oil temperature rise, if the process is long, inside the pump oil temperature is too high, you should stop the pump to check.
    2.5 如果泵内溫度過高而引起自吸困難.可暫時停機,利用出口管路中的液體倒流或直接向泵内補充液體,使泵内液體降溫,即可啟動.2.5 if the high temperature caused by self pump difficult. can temporarily stop, using the export pipeline fluid replacement in the liquid backflow or directly to the pump, cooling the liquid in the pump, can be started.
    2.6 泵在工作過程中因故停泵,需在啟動時,把出口控制閥稍開.這樣既有利于自吸過程中其他從吐出口排出,又能保證泵在較輕的(de)負荷下啟動.2.6 pump in the process of work for pump stopped, at startup, the export control valve slightly open. this is beneficial to both other exported from spitting out during the process of imbibition, and can guarantee the pump starts under a lighter load.
    2.7 泵每工作15-20小時或每次使用前應檢查并及時補充一次10号機械油.2.7 pump every 15 to 20 hours or every time before the use should check and added a number 10 machine oil in time.
    3 停車
    3.1 關閉吐出管路上的閘閥
    3.2 使泵停止轉動
    4 易損件的維護
    4.1 滾動軸承:當油泵長期運動後,油泵磨損到一定程度必須更換
    4.2 前後密封環:當密封環磨損到一定程度時,須進行更換
    4.3 機械密封:在不漏油的情況下,一般不應拆開檢查,若軸承體下端洩漏口處産生嚴重洩露時,則應對機械密封進行拆檢.裝拆機械密封時,必須輕取輕放,注意配合面的清潔,不好好動、靜環表面的(de)光潔度，嚴禁敲擊碰撞。

     自吸離心泵的過流部件    self-g centrifugal pump flow components
     自吸離心泵的(de)過流部件有：吸入室，葉輪，壓出室三個部分。葉輪室是泵的核心，也是流部件的核心。泵通過葉輪對液體的作功，使其能量增加。葉輪按液體流出的方向分為三類： self-g centrifugal pump flow components are: suction chamber, impeller, the pressure out of the room three parts.room is the core of the pump impeller, and also the core of the flow components.of liquid through the impeller pump work, allow it to increase energy.according to the direction of liquid flow impeller is divided into three categories:   
    （1）徑流式葉輪（離心式葉輪）液體是沿着(zhe)與軸線垂直的方向流出葉輪。    （2）斜流式葉輪（混流式葉輪）液體是沿着軸線傾斜的(de)方向流出葉輪。    （3）軸流式葉輪液體流動的(de)方向與軸線平行的(de)。
     葉輪的分類
     葉輪按吸入的方式分為二類：
    （1） 單吸葉輪（即葉輪從一側吸入液體）。    （2） 雙吸葉輪（即葉輪從兩側吸入液體）。   
     葉輪按蓋闆形式分為三類：    （1） 封閉式葉輪。    （2） 敞開式葉輪。    （3） 半開式葉輪
     according to the classification of the impeller impeller suction way is divided into two categories:
(1) single suction impeller (i.e., from one side suction impeller liquid).(i.e., (2) double suction impeller impeller from either side suction liquid).  
impeller press flat form is divided into three categories: (1) closed impeller.(2) open type impeller.(3) half open impeller
   ●特點: cyz自吸泵屬自吸式離心泵系列。具有結構簡單、操作維護方便、運行平穩、排量大、效率高、便于調節，有較強的自吸能力，适用範圍廣等特點。

    ●用途： cyz自吸泵用來輸送汽油、煤油、柴油、航空煤油等石油産品。介質溫度在-20℃～+80℃，是一種優良的船用裝卸油泵，可兼作掃艙水泵。并适用于陸地油庫、油罐車等儲油裝置的(de)油料輸送。也可以用來輸送海水、淡水等。

    ●結構型式： cyz自吸泵采用軸同回液的泵體結構，泵體由吸入室、儲液室、渦旋室、回液孔、氣液分離室等組成。泵的(de)軸承采用單列向心球軸承。在一些泵的軸承體底部設有冷卻室。泵内部高、低壓區間有密封環。軸端采用機械密封。

1.本公司常規産品1-3天發貨,特殊要求或者需定做的産品發貨時間已與客戶協商為準,
2.泵運費方式有兩種:快遞和物流.小泵和小型配件發快遞,其餘體積較大,數量較多,推薦走專線物流貨運,一般南方,中部地區及沿海地區3-5天左右到達.西部,北部較遠的地區以及少數二次中轉地區5-8天左右可到,具體覆蓋範圍請咨詢公司客服人員.
安裝使用:請您根據産品說明書的步驟進行操作,如有問題,請聯系我公司.

1.本公司常規産品1-3天發貨,特殊要求或者需定做的(de)産品發貨時間已與客戶協商為準,
2.泵運費方式有兩種:快遞和物流.小泵和小型配件發快遞,其餘體積較大,數量較多,推薦走專線物流貨運,一般南方,中部地區及沿海地區3-5天左右到達.西部,北部較遠的地區以及少數二次中轉地區5-8天左右可到,具體覆蓋範圍請咨詢公司客服人員.
安裝使用:請您根據産品說明書的步驟進行操作,如有問題,請聯系我公司.